产品中心
- 舒泊润 Superlube
- SUPERLA PJ 2000
- Momentive氮化硼粉末
- Momentive氮化硼涂料
- 食品级硅脂
- 食品级轴承油
- 食品级真空泵油
- 食品级链条油
- 冷冻油
- 食品级冷冻油
- 螺杆式空压机油
- 丙烷冷冻油
- 美国BVA冷冻油
- 烷基苯冷冻油
- BVA空压机油
- BVA碳氢气体压缩机油
- BVA 烷基苯冷冻油
- BVA二氧化碳冷冻油
- 氨冷冻油
- BVA食品级齿轮油
- BVA食品级液压油
- R1234yf冷冻油
- 水溶性高温链条油
- R32冷冻油
- 高温链条油
- 氮化硼高温链条油
- 碳氢气体压缩机油
- 高温油膏
- 食品级硅油
- 食品级压缩机油
- 食品级齿轮油
- 食品级液压油
- 食品级白油
- 食品级润滑脂
- 食品级润滑油
- 合成齿轮油
- 食品级导热油
- 空压机油
- 食品级空压机油
- 合成空压机油
- 定制空压机油
- 活塞式空压机油
- 矿物型空压机油
- 食品级螺杆空压机油
- 食品级活塞空压机油
- 食品级合成空压机油
- UCON 基础油
- 食品级凡士林
- 轴承油
- 混合气体制冷剂压缩机冷冻油
- 真空泵油
- 亚群与陶氏对等表
- 涂层保护液

ArChine Syngear PAG 100
规格:20L、200L
产品简介:Extreme-pressure lubrication without of chlorine- or sulfur-containing additives
ArChine Syngear PAG 100
For Compressors, Drivers, Gears, Anti-wear Hydraulics,
Mobile Equipment and Pumps
Product Description
ArChine Syngear PAG 100 is an extreme-pressure lubricant. Formulated to provide excellent lubrication, stability, and extended service life, they
eliminate many of the problems commonly encountered with petroleum lubricants. ArChine Syngear PAG 100 can provide a variety of cost savings
to users.
Product Features
- Wide temperature range operability
- Highly resistant to oxidation and thermal degradation
- Excellent viscosity-temperature properties eliminate the need for seasonal changeover
- Viscosities are unaffected by high rates of shear
- Excellent lubricity for reduced friction and wear
- Resistant to sludge and varnish formation
- Noncorrosive to metal surfaces—stain-resistant to nonferrous metals
- High flash points
- Extreme-pressure lubrication without of chlorine- or sulfur-containing additives
Typical Physical Properties
Properties |
ArChine Syngear PAG 100 |
Appearance |
Light yellow, clear liquid |
Density, 20℃ g/cm3 |
0.991 |
Viscosity, 40℃ mm2/s |
107.0 |
Viscosity, 100℃ mm2/s |
18.1 |
Viscosity Index |
188 |
Flash Point (Open cup, ℃) |
274 |
Fire Point, ℃ |
296 |
Pour Point, ℃ |
-42 |
Copper Strip Test, 100℃, 3hr , grade |
1 |
Foaming properties 24℃ 93.5℃ 24℃ |
10/0 10/0 10/0 |
Selecting ArChine Syngear PAG 100
AGMA Viscosity Grades
Because of the high viscosity index exhibited by ArChine Syngear PAG (46-680 vs. 90-100 for most petroleum gear lubricants), they are not
classified by one AGMA viscosity rating.
ArChine Syngear PAG lubricants will effectively span 2 or 3 AGMA petroleum lubricant grades over the operating range of most gear boxes.
By knowing either the viscosity required at the operating temperature or the AGMA rating of the current lubricant, the appropriate performing
ArChine Syngear PAG L lubricant can easily be chosen.
Selection Guide for ArChine Syngear PAG
Lubricant |
AGMA Grades Usually Replaced |
ArChine Syngear PAG 46 |
1-2 |
ArChine Syngear PAG 68 |
2-3 |
ArChine Syngear PAG 150 |
3-6 |
ArChine Syngear PAG 220 |
5-7 |
ArChine Syngear PAG 460 |
6-8 |
ArChine Syngear PAG 680 |
8-8A |
Converting to ArChine Syngear PAG 100
Installation of ArChine Syngear PAG 100 lubricants into machinery that previously contained petroleum oils should follow the recommended flush
procedure below:
1.Drain previous lubricant from the equipment.
2.Replace oil filters.
3.Fill the system with the ArChine Syngear PAG 100 lubricant to be used. Run or circulate under normal operating conditions for 24 hours.
4.ArChine Syngear PAG 100 lubricants will generally clean varnish and sludge build-up formed from petroleum oils.
5.Thoroughly drain the ArChine Syngear PAG 100 lubricant from the system while warm.
6.Inspect the oil filters and replace as needed.
7.Fill the equipment with fresh ArChine Syngear PAG 100 lubricant and begin normal operation.
8.Inspect and change filters as required. This procedure should be followed for best results. Residual petroleum lubricant can usually be
tolerated at low levels in the ArChine Syngear PAG 100 lubricant.
Monitoring ArChine Syngear PAG
Although ArChine Syngear PAG 100 lubricant will show a greatly extended service life under most conditions, one should not neglect to
perform periodic maintenance and inspection, which will help ensure continued trouble-free operation.
*Typical data shall not be used as product specifications.